• Surface Inlets are designed for a flush finish for your convenience.
• Typical applications include garage drains, parking lots, or anywhere surface drainage is necessary.
• Castings are made to fit inside standard drainage tile.
• Available sizes 4"-24"
• Pedestrian Traffic ONLY

Mitered Drain™ is perfect for use in hard to drain areas where lack of grade difference is a problem. Because of its sloped grate, water flows directly into the pipe eliminating the drop typical in conventional inlets allowing for better drainage in flat areas that need extra slope to achieve proper drainage.  

For use with culverts, under sidewalks, in planter areas, creeks and swales or any difficult-to-drain location.

• Light Duty retail / consumer model
• DIFFERENT DISCHARGE DESIGN THAN THE CONTRACTOR GRADE GRAY AND BLACK MODELS
• 3:1 Slope  
• HDPE grates have UV inhibitor
• Area of grate opening (9.85 sq. in.)
• Set screws are type 300 stainless steel
• Not recommended for traffic loads
• Made in USA

Mitered Drain™ is perfect for use in hard to drain areas where lack of grade difference is a problem. Because of its sloped grate, water flows directly into the pipe eliminating the drop typical in conventional inlets allowing for better drainage in flat areas that need extra slope to achieve proper drainage.  

For use with culverts, under sidewalks, in planter areas, creeks and swales or any difficult-to-drain location.

• Light Duty retail / consumer model
• DIFFERENT DISCHARGE DESIGN THAN THE CONTRACTOR GRADE GRAY AND BLACK MODELS
• 3:1 Slope  
• HDPE grates have UV inhibitor
• Area of grate opening (9.85 sq. in.)
• Set screws are type 300 stainless steel
• Not recommended for traffic loads
• Made in USA

Mitered Drain™ is perfect for use in hard to drain areas where lack of grade difference is a problem. Because of its sloped grate, water flows directly into the pipe eliminating the drop typical in conventional inlets allowing for better drainage in flat areas that need extra slope to achieve proper drainage.  

For use with culverts, under sidewalks, in planter areas, creeks and swales or any difficult-to-drain location.

• 3:1 Slope  
• HDPE grates have UV inhibitor
• Area of grate opening (10.4 sq. in.)
• Set screws are type 300 stainless steel
• Not recommended for traffic loads
• Made in USA

Mitered Drain™ is perfect for use in hard to drain areas where lack of grade difference is a problem. Because of its sloped grate, water flows directly into the pipe eliminating the drop typical in conventional inlets allowing for better drainage in flat areas that need extra slope to achieve proper drainage.  

For use with culverts, under sidewalks, in planter areas, creeks and swales or any difficult-to-drain location.

• 3:1 Slope  
• HDPE grates have UV inhibitor
• Area of grate opening (10.4 sq. in.)
• Set screws are type 300 stainless steel
• Not recommended for traffic loads
• Made in USA

Fits into SDR35 ASTM D3034 fittings

Snap In Drain

• Fits inside 3" PVC Schedule 40 DWV pipe
• Allows cutting pipe flush with the floor level
• May be solvent welded or simply inserted into the pipe

Architectural grade, structural retaining wall drain components are designed to hide exposed drain pipes in large and small, residential and commercial retaining walls while providing optimum egress of water flow (weeping).

Wall Drains can also be used on barbecue islands, outdoor kitchens, fire pits and other applications to complete a pleasing, continuous wall face without the unsightly interruptions of intermittent drains or air vents.

• Durable laser-cut stainless steel with powder coated faux finish inspired by colors in natural stone.
• Built-in anchor points and locking tabs for fast installation.
• Available in 7 colors
• Available in 4 sizes: 3" x 3" for 3" blocks, 4" x 4" for 4" blocks, 5" x 5" for 7" & 8" tall blocks and 6' x 6" for 6" blocks.
• Made in USA
• Not to be used with roof drains as solids may cause clogging.

INSTALLATION INSTRUCTIONS:

Bend side tabs outward and fit to lock against neighboring wall blocks. Optional: Run a bead of adhesive across the holes on the top and bottom flange. Place drain into wall geometry same as an actual block on first course at ground level. Place drainpipe or aggregate against back of drain, filling all voids. Not to be used with roof drains as solids may cause clogging.

Architectural grade, structural retaining wall drain components are designed to hide exposed drain pipes in large and small, residential and commercial retaining walls while providing optimum egress of water flow (weeping).

Wall Drains can also be used on barbecue islands, outdoor kitchens, fire pits and other applications to complete a pleasing, continuous wall face without the unsightly interruptions of intermittent drains or air vents.

• Durable laser-cut stainless steel with powder coated faux finish inspired by colors in natural stone.
• Built-in anchor points and locking tabs for fast installation.
• Available in 7 colors
• Available in 4 sizes: 3" x 3" for 3" blocks, 4" x 4" for 4" blocks, 5" x 5" for 7" & 8" tall blocks and 6' x 6" for 6" blocks.
• Made in USA
• Not to be used with roof drains as solids may cause clogging.

INSTALLATION INSTRUCTIONS:

Bend side tabs outward and fit to lock against neighboring wall blocks. Optional: Run a bead of adhesive across the holes on the top and bottom flange. Place drain into wall geometry same as an actual block on first course at ground level. Place drainpipe or aggregate against back of drain, filling all voids. Not to be used with roof drains as solids may cause clogging.

Architectural grade, structural retaining wall drain components are designed to hide exposed drain pipes in large and small, residential and commercial retaining walls while providing optimum egress of water flow (weeping).

Wall Drains can also be used on barbecue islands, outdoor kitchens, fire pits and other applications to complete a pleasing, continuous wall face without the unsightly interruptions of intermittent drains or air vents.

• Durable laser-cut stainless steel with powder coated faux finish inspired by colors in natural stone.
• Built-in anchor points and locking tabs for fast installation.
• Available in 7 colors
• Available in 4 sizes: 3" x 3" for 3" blocks, 4" x 4" for 4" blocks, 5" x 5" for 7" & 8" tall blocks and 6' x 6" for 6" blocks.
• Made in USA
• Not to be used with roof drains as solids may cause clogging.

INSTALLATION INSTRUCTIONS:

Bend side tabs outward and fit to lock against neighboring wall blocks. Optional: Run a bead of adhesive across the holes on the top and bottom flange. Place drain into wall geometry same as an actual block on first course at ground level. Place drainpipe or aggregate against back of drain, filling all voids. Not to be used with roof drains as solids may cause clogging.

Architectural grade, structural retaining wall drain components are designed to hide exposed drain pipes in large and small, residential and commercial retaining walls while providing optimum egress of water flow (weeping).

Wall Drains can also be used on barbecue islands, outdoor kitchens, fire pits and other applications to complete a pleasing, continuous wall face without the unsightly interruptions of intermittent drains or air vents.

• Durable laser-cut stainless steel with powder coated faux finish inspired by colors in natural stone.
• Built-in anchor points and locking tabs for fast installation.
• Available in 7 colors
• Available in 4 sizes: 3" x 3" for 3" blocks, 4" x 4" for 4" blocks, 5" x 5" for 7" & 8" tall blocks and 6' x 6" for 6" blocks.
• Made in USA
• Not to be used with roof drains as solids may cause clogging.

INSTALLATION INSTRUCTIONS:

Bend side tabs outward and fit to lock against neighboring wall blocks. Optional: Run a bead of adhesive across the holes on the top and bottom flange. Place drain into wall geometry same as an actual block on first course at ground level. Place drainpipe or aggregate against back of drain, filling all voids. Not to be used with roof drains as solids may cause clogging.

Architectural grade, structural retaining wall drain components are designed to hide exposed drain pipes in large and small, residential and commercial retaining walls while providing optimum egress of water flow (weeping).

Wall Drains can also be used on barbecue islands, outdoor kitchens, fire pits and other applications to complete a pleasing, continuous wall face without the unsightly interruptions of intermittent drains or air vents.

• Durable laser-cut stainless steel with powder coated faux finish inspired by colors in natural stone.
• Built-in anchor points and locking tabs for fast installation.
• Available in 7 colors
• Available in 4 sizes: 3" x 3" for 3" blocks, 4" x 4" for 4" blocks, 5" x 5" for 7" & 8" tall blocks and 6' x 6" for 6" blocks.
• Made in USA
• Not to be used with roof drains as solids may cause clogging.

INSTALLATION INSTRUCTIONS:

Bend side tabs outward and fit to lock against neighboring wall blocks. Optional: Run a bead of adhesive across the holes on the top and bottom flange. Place drain into wall geometry same as an actual block on first course at ground level. Place drainpipe or aggregate against back of drain, filling all voids. Not to be used with roof drains as solids may cause clogging.