• Both ends fit over Copper or Copper Tube Size (CTS) Polyethylene
• Insert stiffeners required on all flexible plastic pipe connections
• Use 6131 or 6133 Series stiffeners on all flexible plastic pipe connections
• Series No-Lead 74761Q
• Manufactured in compliance with ANSI/AWWA C800 (latest revision)
• Brass components in contact with potable water conform to ASTM B584, UNS C89833 (latest revision) and identified with “NL"
• Certified to NSF/ANSI 61 and NSF/ANSI 372
• Brass components not in contact with potable water conform to ASTM B62 and ASTM B584, UNS C83600 -85-5-5-5 (latest revision)
• Large wrench flats provided for proper installation
• They are designed and tested for cold potable water only.
• EPDM rubber gaskets are used in our compression fittings.

The simple steps listed below will make your job easier and assure fast, safe and watertight connections:

1. Service tubing should always be snaked in the ditch.

2. Use a tube or pipe cutter to assure a square end. Make sure pipe is round. On copper tubing, use a rounding tool, if necessary. Surface should be clean and free of nicks.

3. Insert stiffeners must be used with plastic tubing.

4. Stab tube through the nut and into the socket of the valve or fitting until it bottoms out (some fittings may or may not have a stop).

5. Tighten the McQuik "Q" Series nut to the stop. The end face of the nut is to contact the stop face of the body.

6. PRESSURE TEST FOR LEAKS BEFORE BACKFILLING.

7. USE ONLY ON COLD WATER SERVICES.

CAUTIONS

1. Protect threads. Avoid loose fitting wrenches. Do not drop or impact.

2. Use extra care with high water pressures (over 100 PSIG) and pipe or tubing over 1". Consult factory if desired.

3. Inspect and test all joints, valves and fittings before backfilling.

4. Backfill carefully so as to avoid damage to the service line and connections. Looping of the service lines is recommended to minimize strain.

5. DO NOT use Vaseline, plumber's grease, or any other petroleum based product on seals or o-rings.

• One end fits over Copper or Copper Tube Size (CTS) Polyethylene
• One end threads over male pipe threads
• Insert stiffeners required on all flexible plastic pipe connections
• Use 6131 or 6133 Series stiffeners on all flexible plastic pipe connections
• Series No-Lead 74779M
• Manufactured in compliance with ANSI/AWWA C800 (latest revision)
• Brass components in contact with potable water conform to ASTM B584, UNS C89833 (latest revision) and identified with “NL"
• Certified to NSF/ANSI 61 and NSF/ANSI 372
• Brass components not in contact with potable water conform to ASTM B62 and ASTM B584, UNS C83600 -85-5-5-5 (latest revision)
• Large wrench flats provided for proper installation
• They are designed and tested for cold potable water only.
• EPDM rubber gaskets are used in our compression fittings.

• One end fits over Copper or Copper Tube Size (CTS) Polyethylene
• One end threads into female pipe threads
• Insert stiffeners required on all flexible plastic pipe connections
• Use 6131 or 6133 Series stiffeners on all flexible plastic pipe connections
• Series No-Lead 74779MQ
• Manufactured in compliance with ANSI/AWWA C800 (latest revision)
• Brass components in contact with potable water conform to ASTM B584, UNS C89833 (latest revision) and identified with “NL"
• Certified to NSF/ANSI 61 and NSF/ANSI 372
• Brass components not in contact with potable water conform to ASTM B62 and ASTM B584, UNS C83600 -85-5-5-5 (latest revision)
• Large wrench flats provided for proper installation
• They are designed and tested for cold potable water only.
• EPDM rubber gaskets are used in our compression fittings.

• All ends fits over Copper or Copper Tube Size (CTS) Polyethylene
• Insert stiffeners required on all flexible plastic pipe connections
• Use 6131 or 6133 Series stiffeners on all flexible plastic pipe connections
• Series No-Lead 74760Q
• Manufactured in compliance with ANSI/AWWA C800 (latest revision)
• Brass components in contact with potable water conform to ASTM B584, UNS C89833 (latest revision) and identified with “NL"
• Certified to NSF/ANSI 61 and NSF/ANSI 372
• Brass components not in contact with potable water conform to ASTM B62 and ASTM B584, UNS C83600 -85-5-5-5 (latest revision)
• Large wrench flats provided for proper installation
• They are designed and tested for cold potable water only.
• EPDM rubber gaskets are used in our compression fittings.

The simple steps listed below will make your job easier and assure fast, safe and watertight connections:

1. Service tubing should always be snaked in the ditch.

2. Use a tube or pipe cutter to assure a square end. Make sure pipe is round. On copper tubing, use a rounding tool, if necessary. Surface should be clean and free of nicks.

3. Insert stiffeners must be used with plastic tubing.

4. Stab tube through the nut and into the socket of the valve or fitting until it bottoms out (some fittings may or may not have a stop).

5. Tighten the McQuik "Q" Series nut to the stop. The end face of the nut is to contact the stop face of the body.

6. PRESSURE TEST FOR LEAKS BEFORE BACKFILLING.

7. USE ONLY ON COLD WATER SERVICES.

CAUTIONS

1. Protect threads. Avoid loose fitting wrenches. Do not drop or impact.

2. Use extra care with high water pressures (over 100 PSIG) and pipe or tubing over 1". Consult factory if desired.

3. Inspect and test all joints, valves and fittings before backfilling.

4. Backfill carefully so as to avoid damage to the service line and connections. Looping of the service lines is recommended to minimize strain.

5. DO NOT use Vaseline, plumber's grease, or any other petroleum based product on seals or o-rings.

• Two ends fits over Copper or Copper Tube Size (CTS) Polyethylene
• Outlet / Branch threads into female pipe threads
• Insert stiffeners required on all flexible plastic pipe connections
• Use 6131 or 6133 Series stiffeners on all flexible plastic pipe connections
• Series No-Lead 74762Q
• Manufactured in compliance with ANSI/AWWA C800 (latest revision)
• Brass components in contact with potable water conform to ASTM B584, UNS C89833 (latest revision) and identified with “NL"
• Certified to NSF/ANSI 61 and NSF/ANSI 372
• Brass components not in contact with potable water conform to ASTM B62 and ASTM B584, UNS C83600 -85-5-5-5 (latest revision)
• Large wrench flats provided for proper installation
• They are designed and tested for cold potable water only.
• EPDM rubber gaskets are used in our compression fittings.

The simple steps listed below will make your job easier and assure fast, safe and watertight connections:

1. Service tubing should always be snaked in the ditch.

2. Use a tube or pipe cutter to assure a square end. Make sure pipe is round. On copper tubing, use a rounding tool, if necessary. Surface should be clean and free of nicks.

3. Insert stiffeners must be used with plastic tubing.

4. Stab tube through the nut and into the socket of the valve or fitting until it bottoms out (some fittings may or may not have a stop).

5. Tighten the McQuik "Q" Series nut to the stop. The end face of the nut is to contact the stop face of the body.

6. PRESSURE TEST FOR LEAKS BEFORE BACKFILLING.

7. USE ONLY ON COLD WATER SERVICES.

CAUTIONS

1. Protect threads. Avoid loose fitting wrenches. Do not drop or impact.

2. Use extra care with high water pressures (over 100 PSIG) and pipe or tubing over 1". Consult factory if desired.

3. Inspect and test all joints, valves and fittings before backfilling.

4. Backfill carefully so as to avoid damage to the service line and connections. Looping of the service lines is recommended to minimize strain.

5. DO NOT use Vaseline, plumber's grease, or any other petroleum based product on seals or o-rings.

• Tighten-to-torque required - noted on installation instructions
• Insert stiffeners required on all flexible plastic pipe connections
• Use 6131 or 6133 Series stiffeners for CTS on flexible plastic pipe connections
• Use 6136 Series stiffeners for PEP on flexible plastic pipe connections
• Meet and exceeds AWWA C800-14, which requires fittings to be suitable for a water pressure of 150 PSIG
• Withstands the same pressures as the tubing, but must not be used with pressures exceeding 300 PSIG
• Double Leed Thread allows for compression nut to be assembled in half the time of a standard compression nut and eliminates the possibility of assembling an incompatible nut to these fittings.
• Designed for underground and aboveground cold potable water systems
• Manufactured in compliance with ANSI/AWWA C800 (latest revision)
• Brass components in contact with potable water conform to ASTM B584, UNS C89833 (latest revision) and identified with “NL"
• Certified to NSF/ANSI 61 and NSF/ANSI 372
• Brass components not in contact with potable water conform to ASTM B62 and ASTM B584, UNS C83600 -85-5-5-5 (latest revision)
• Large wrench flats provided for proper installation

The simple steps listed below will make your job easier and assure fast, safe and watertight connections:

1. Service tubing should always be snaked in the ditch.

2. Use a tube or pipe cutter to assure a square end. Make sure pipe is round. On copper tubing, use a rounding tool, if necessary. Surface should be clean and free of nicks.

3. Insert stiffeners must be used with plastic tubing.

4. Stab tube through the nut and into the socket of the valve or fitting until it bottoms out (some fittings may or may not have a stop).

5. Tighten-to torque required. Noted on Installation instructions.

6. PRESSURE TEST FOR LEAKS BEFORE BACKFILLING.

7. USE ONLY ON COLD WATER SERVICES.

CAUTIONS

1. Protect threads. Avoid loose fitting wrenches. Do not drop or impact.

2. Inspect and test all joints, valves and fittings before backfilling.

3. Backfill carefully so as to avoid damage to the service line and connections. Looping of the service lines is recommended to minimize strain.

4. DO NOT use Vaseline, plumber's grease, or any other petroleum based product on seals or o-rings.

• Tighten-to-torque required - noted on installation instructions
• Insert stiffeners required on all flexible plastic pipe connections
• Use 6131 or 6133 Series stiffeners for CTS on flexible plastic pipe connections
• Use 6136 Series stiffeners for PEP on flexible plastic pipe connections
• Meet and exceeds AWWA C800-14, which requires fittings to be suitable for a water pressure of 150 PSIG
• Withstands the same pressures as the tubing, but must not be used with pressures exceeding 300 PSIG
• Double Leed Thread allows for compression nut to be assembled in half the time of a standard compression nut and eliminates the possibility of assembling an incompatible nut to these fittings.
• Designed for underground and aboveground cold potable water systems
• Manufactured in compliance with ANSI/AWWA C800 (latest revision)
• Brass components in contact with potable water conform to ASTM B584, UNS C89833 (latest revision) and identified with “NL"
• Certified to NSF/ANSI 61 and NSF/ANSI 372
• Brass components not in contact with potable water conform to ASTM B62 and ASTM B584, UNS C83600 -85-5-5-5 (latest revision)
• Large wrench flats provided for proper installation

The simple steps listed below will make your job easier and assure fast, safe and watertight connections:

1. Service tubing should always be snaked in the ditch.

2. Use a tube or pipe cutter to assure a square end. Make sure pipe is round. On copper tubing, use a rounding tool, if necessary. Surface should be clean and free of nicks.

3. Insert stiffeners must be used with plastic tubing.

4. Stab tube through the nut and into the socket of the valve or fitting until it bottoms out (some fittings may or may not have a stop).

5. Tighten-to torque required. Noted on Installation instructions.

6. PRESSURE TEST FOR LEAKS BEFORE BACKFILLING.

7. USE ONLY ON COLD WATER SERVICES.

CAUTIONS

1. Protect threads. Avoid loose fitting wrenches. Do not drop or impact.

2. Inspect and test all joints, valves and fittings before backfilling.

3. Backfill carefully so as to avoid damage to the service line and connections. Looping of the service lines is recommended to minimize strain.

4. DO NOT use Vaseline, plumber's grease, or any other petroleum based product on seals or o-rings.

• One end fits over Copper or Copper Tube Size (CTS) Polyethylene
• One end threads over male pipe threads
• Insert stiffeners required on all flexible plastic pipe connections
• Use 6131 or 6133 Series stiffeners on all flexible plastic pipe connections
• Series No-Lead 74754Q
• Manufactured in compliance with ANSI/AWWA C800 (latest revision)
• Brass components in contact with potable water conform to ASTM B584, UNS C89833 (latest revision) and identified with “NL"
• Certified to NSF/ANSI 61 and NSF/ANSI 372
• Brass components not in contact with potable water conform to ASTM B62 and ASTM B584, UNS C83600 -85-5-5-5 (latest revision)
• Large wrench flats provided for proper installation
• They are designed and tested for cold potable water only.
• EPDM rubber gaskets are used in our compression fittings.

The simple steps listed below will make your job easier and assure fast, safe and watertight connections:

1. Service tubing should always be snaked in the ditch.

2. Use a tube or pipe cutter to assure a square end. Make sure pipe is round. On copper tubing, use a rounding tool, if necessary. Surface should be clean and free of nicks.

3. Insert stiffeners must be used with plastic tubing.

4. Stab tube through the nut and into the socket of the valve or fitting until it bottoms out (some fittings may or may not have a stop).

5. Tighten the McQuik "Q" Series nut to the stop. The end face of the nut is to contact the stop face of the body.

6. PRESSURE TEST FOR LEAKS BEFORE BACKFILLING.

7. USE ONLY ON COLD WATER SERVICES.

CAUTIONS

1. Protect threads. Avoid loose fitting wrenches. Do not drop or impact.

2. Use extra care with high water pressures (over 100 PSIG) and pipe or tubing over 1". Consult factory if desired.

3. Inspect and test all joints, valves and fittings before backfilling.

4. Backfill carefully so as to avoid damage to the service line and connections. Looping of the service lines is recommended to minimize strain.

5. DO NOT use Vaseline, plumber's grease, or any other petroleum based product on seals or o-rings.

• One end fits over Copper or Copper Tube Size (CTS) Polyethylene
• One end threads into female pipe threads
• Insert stiffeners required on all flexible plastic pipe connections
• Use 6131 or 6133 Series stiffeners on all flexible plastic pipe connections
• Series No-Lead 74753Q
• Manufactured in compliance with ANSI/AWWA C800 (latest revision)
• Brass components in contact with potable water conform to ASTM B584, UNS C89833 (latest revision) and identified with “NL"
• Certified to NSF/ANSI 61 and NSF/ANSI 372
• Brass components not in contact with potable water conform to ASTM B62 and ASTM B584, UNS C83600 -85-5-5-5 (latest revision)
• Large wrench flats provided for proper installation
• They are designed and tested for cold potable water only.
• EPDM rubber gaskets are used in our compression fittings.

The simple steps listed below will make your job easier and assure fast, safe and watertight connections:

1. Service tubing should always be snaked in the ditch.

2. Use a tube or pipe cutter to assure a square end. Make sure pipe is round. On copper tubing, use a rounding tool, if necessary. Surface should be clean and free of nicks.

3. Insert stiffeners must be used with plastic tubing.

4. Stab tube through the nut and into the socket of the valve or fitting until it bottoms out (some fittings may or may not have a stop).

5. Tighten the McQuik "Q" Series nut to the stop. The end face of the nut is to contact the stop face of the body.

6. PRESSURE TEST FOR LEAKS BEFORE BACKFILLING.

7. USE ONLY ON COLD WATER SERVICES.

CAUTIONS

1. Protect threads. Avoid loose fitting wrenches. Do not drop or impact.

2. Use extra care with high water pressures (over 100 PSIG) and pipe or tubing over 1". Consult factory if desired.

3. Inspect and test all joints, valves and fittings before backfilling.

4. Backfill carefully so as to avoid damage to the service line and connections. Looping of the service lines is recommended to minimize strain.

5. DO NOT use Vaseline, plumber's grease, or any other petroleum based product on seals or o-rings.

• All ends fits over Copper or Copper Tube Size (CTS) Polyethylene
• Insert stiffeners required on all flexible plastic pipe connections
• Use 6131 or 6133 Series stiffeners on all flexible plastic pipe connections
• Series No-Lead 74760Q
• Manufactured in compliance with ANSI/AWWA C800 (latest revision)
• Brass components in contact with potable water conform to ASTM B584, UNS C89833 (latest revision) and identified with “NL"
• Certified to NSF/ANSI 61 and NSF/ANSI 372
• Brass components not in contact with potable water conform to ASTM B62 and ASTM B584, UNS C83600 -85-5-5-5 (latest revision)
• Large wrench flats provided for proper installation
• They are designed and tested for cold potable water only.
• EPDM rubber gaskets are used in our compression fittings.

The simple steps listed below will make your job easier and assure fast, safe and watertight connections:

1. Service tubing should always be snaked in the ditch.

2. Use a tube or pipe cutter to assure a square end. Make sure pipe is round. On copper tubing, use a rounding tool, if necessary. Surface should be clean and free of nicks.

3. Insert stiffeners must be used with plastic tubing.

4. Stab tube through the nut and into the socket of the valve or fitting until it bottoms out (some fittings may or may not have a stop).

5. Tighten the McQuik "Q" Series nut to the stop. The end face of the nut is to contact the stop face of the body.

6. PRESSURE TEST FOR LEAKS BEFORE BACKFILLING.

7. USE ONLY ON COLD WATER SERVICES.

CAUTIONS

1. Protect threads. Avoid loose fitting wrenches. Do not drop or impact.

2. Use extra care with high water pressures (over 100 PSIG) and pipe or tubing over 1". Consult factory if desired.

3. Inspect and test all joints, valves and fittings before backfilling.

4. Backfill carefully so as to avoid damage to the service line and connections. Looping of the service lines is recommended to minimize strain.

5. DO NOT use Vaseline, plumber's grease, or any other petroleum based product on seals or o-rings.