WELD-ONŒ 735Ž Wet ´N FastŽ is a blue, low VOC emission, medium bodied, extremely fast setting, high strength PVC solvent cement for all classes and schedules of pipe and fittings with interference fit through 6 inch (160 mm) diameter, Schedule 80 through 4 inch (110 mm) diameter.

APPLICATION: WELD-ON 735 Wet ´N Fast is for use on rigid and flexible PVC pipe and fittings, including PVC foam core DWV. It is specially formulated for applications where conditions are wet and/or quick pressurization of the piping systems is desired. It was developed to answer specific needs in the plumbing industry but may also be used in irrigation, pool, spa and other applications. Can be used without primer on non-pressure systems if local codes permit.

Detailed directions on making solvent cemented joints are printed on the container label. An installation DVD/CD covering solvent cementing is available. It not only describes the basic principles of solvent cementing, but also covers the handling, storage and use of our products. It is highly recommended that the installer review the instructions supplied by the pipe and fitting manufacturer.

NOTE: WELD-ON solvent cements must never be used in a PVC system using or being tested by compressed air or gases; including air-over-water booster.

• Medium-bodied, very fast-setting, low-VOC PVC cement for all classes and schedules with interference fit through 6" (160 mm) diameter, Schedule 80 through 4" (110 mm) diameter
• Premium formula for all weather conditions (-15F to 110F, -26C to 43C)
• Can be used without primer on non-pressure systems if local code
• Plumbing quality cement for wet conditions and/or quick pressurization
• Can be used without primer on non-pressure systems if local codes permit
• Meets ASTM D 2564 Standard
• Meets SCAQMD Rule 1168/316A
• Compliant with LEEDŒ (Leadership in Energy and Environmental Design). When using this Weld-On low VOC product, credit can be claimed for LEED Green Building Rating System - Indoor Environmental Quality.
• Listed by NSF International for compliance with ASTM D 2564, NSF/ANSI Standard 14, and NSF/ANSI Standard 61 for use on potable water, drain, waste, vent and sewer applications.
• Listed by IAPMO for compliance with ASTM D 2564 and applicable sections of the latest edition of the Uniform Plumbing CodeŒ.

Weld-On®780™is a clear, ultra low VOC emission, regular bodied, fast setting, high strength PVC solvent cement for all classes and schedules. It is used for pipe and fitting with an interference fit through 4inches (110mm) diameter, Schedule 80 up to 2 inches (63mm).

APPLICATION: Weld-On 780 is for use on all types of PVC plastic pipe plumbing applications, including potable water pressure systems, sewer, drain, waste and vent systems.

• Formulated for all classes and schedules with interference fit through 4" (110 mm) diameter (not for Schedule 80) for plumbing applications
• Regular-bodied, fast-setting, low-VOC PVC cement
• Available in clear
• Meets ASTM D 2564 Standard
• Meets SCAQMD Rule 1168/316A
• Compliant with LEEDŒ (Leadership in Energy and Environmental Design). When using this Weld-On low VOC product, credit can be claimed for LEED Green Building Rating System - Indoor Environmental Quality.
• Listed by NSF International for compliance with ASTM D 2564, NSF/ANSI Standard 14, and NSF/ANSI Standard 61 for use on potable water, drain, waste, vent and sewer applications.
• Listed by IAPMO for compliance with ASTM D 2564 and applicable sections of the latest edition of the Uniform Plumbing Code.

Weld-On 781 is for use on all types of PVC plastic pipe plumbing applications, including potable water pressure systems, sewer and drain/waste/vent systems.

APPLICATION: Weld-On 781 is for use on all types of PVC plastic pipe plumbing applications, including potable water pressure systems, sewer and drain/waste/vent systems.

• Medium-bodied, fast-setting, low-VOC PVC cement
• Formulated for all classes and schedules with interference fit through 6" (160 mm) diameter, Schedule 80 through 4" (110 mm) diameter for plumbing applications
• Can be used without primer on non-pressure systems if local code
• Available in clear and gray
• Meets ASTM D 2564 Standard
• Meets SCAQMD Rule 1168/316A
• Compliant with LEEDŒ (Leadership in Energy and Environmental Design). When using this Weld-On low VOC product, credit can be claimed for LEED Green Building Rating System - Indoor Environmental Quality.
• Listed by NSF International for compliance with ASTM D 2564, NSF/ANSI Standard 14, and NSF/ANSI Standard 61 for use on potable water, drain, waste, vent and sewer applications.
• Listed by IAPMO for compliance with ASTM D 2564 and applicable sections of the latest edition of the Uniform Plumbing CodeŒ.

Weld-On 781 is for use on all types of PVC plastic pipe plumbing applications, including potable water pressure systems, sewer and drain/waste/vent systems.

APPLICATION: Weld-On 781 is for use on all types of PVC plastic pipe plumbing applications, including potable water pressure systems, sewer and drain/waste/vent systems.

• Medium-bodied, fast-setting, low-VOC PVC cement
• Formulated for all classes and schedules with interference fit through 6" (160 mm) diameter, Schedule 80 through 4" (110 mm) diameter for plumbing applications
• Can be used without primer on non-pressure systems if local code
• Available in clear and gray
• Meets ASTM D 2564 Standard
• Meets SCAQMD Rule 1168/316A
• Compliant with LEEDŒ (Leadership in Energy and Environmental Design). When using this Weld-On low VOC product, credit can be claimed for LEED Green Building Rating System - Indoor Environmental Quality.
• Listed by NSF International for compliance with ASTM D 2564, NSF/ANSI Standard 14, and NSF/ANSI Standard 61 for use on potable water, drain, waste, vent and sewer applications.
• Listed by IAPMO for compliance with ASTM D 2564 and applicable sections of the latest edition of the Uniform Plumbing CodeŒ.

Weld-On 781 is for use on all types of PVC plastic pipe plumbing applications, including potable water pressure systems, sewer and drain/waste/vent systems.

APPLICATION: Weld-On 781 is for use on all types of PVC plastic pipe plumbing applications, including potable water pressure systems, sewer and drain/waste/vent systems.

• Medium-bodied, fast-setting, low-VOC PVC cement
• Formulated for all classes and schedules with interference fit through 6" (160 mm) diameter, Schedule 80 through 4" (110 mm) diameter for plumbing applications
• Can be used without primer on non-pressure systems if local code
• Available in clear and gray
• Meets ASTM D 2564 Standard
• Meets SCAQMD Rule 1168/316A
• Compliant with LEEDŒ (Leadership in Energy and Environmental Design). When using this Weld-On low VOC product, credit can be claimed for LEED Green Building Rating System - Indoor Environmental Quality.
• Listed by NSF International for compliance with ASTM D 2564, NSF/ANSI Standard 14, and NSF/ANSI Standard 61 for use on potable water, drain, waste, vent and sewer applications.
• Listed by IAPMO for compliance with ASTM D 2564 and applicable sections of the latest edition of the Uniform Plumbing CodeŒ.

Weld-OnŒ 782Ž is a clear or gray, low VOC emission, heavy bodied, medium setting, high strength PVC solvent cement for all classes and schedules of pipe and fittings, including Schedule 80, with interference fit through 12 inch (315 mm) diameter.

APPLICATION: Weld-On 782 is for use on all types of PVC plastic pipe plumbing applications, including potable water pressure systems, sewer and drain/waste/vent systems. Weld-On 782 has good gap filling properties and is recommended for solvent cementing joints where a sizable gap exists between pipe and fitting _ e.g. large pipe sizes _ and when more working time is required in warm weather..

• Heavy-bodied, medium-setting, low-VOC PVC cement
• Formulated for all classes and schedules with interference fit through 12" (315 mm) diameter (non-pressure applications only up to 18") for plumbing applications
• Good gap-filling properties
• Medium-setting times allow more working time in warm weather
• Available in clear and gray
• Meets ASTM D 2564 Standard
• Meets SCAQMD Rule 1168/316A
• Compliant with LEEDŒ (Leadership in Energy and Environmental Design). When using this Weld-On low VOC product, credit can be claimed for LEED Green Building Rating System - Indoor Environmental Quality.
• Listed by NSF International for compliance with ASTM D 2564, NSF/ANSI Standard 14, and NSF/ANSI Standard 61 for use on potable water, drain, waste, vent and sewer applications.
• Listed by IAPMO for compliance with ASTM D 2564 and applicable sections of the latest edition of the Uniform Plumbing CodeŒ.

Weld-OnŒ 782Ž is a clear or gray, low VOC emission, heavy bodied, medium setting, high strength PVC solvent cement for all classes and schedules of pipe and fittings, including Schedule 80, with interference fit through 12 inch (315 mm) diameter.

APPLICATION: Weld-On 782 is for use on all types of PVC plastic pipe plumbing applications, including potable water pressure systems, sewer and drain/waste/vent systems. Weld-On 782 has good gap filling properties and is recommended for solvent cementing joints where a sizable gap exists between pipe and fitting _ e.g. large pipe sizes _ and when more working time is required in warm weather..

• Heavy-bodied, medium-setting, low-VOC PVC cement
• Formulated for all classes and schedules with interference fit through 12" (315 mm) diameter (non-pressure applications only up to 18") for plumbing applications
• Good gap-filling properties
• Medium-setting times allow more working time in warm weather
• Available in clear and gray
• Meets ASTM D 2564 Standard
• Meets SCAQMD Rule 1168/316A
• Compliant with LEEDŒ (Leadership in Energy and Environmental Design). When using this Weld-On low VOC product, credit can be claimed for LEED Green Building Rating System - Indoor Environmental Quality.
• Listed by NSF International for compliance with ASTM D 2564, NSF/ANSI Standard 14, and NSF/ANSI Standard 61 for use on potable water, drain, waste, vent and sewer applications.
• Listed by IAPMO for compliance with ASTM D 2564 and applicable sections of the latest edition of the Uniform Plumbing CodeŒ.

Compatible with both PVC and CPVC piping, Weld-On 790 Multi-Purpose Solvent Cement offers versatility to contractors working with diverse piping systems. This pipe cement creates a deep, high-contact fusion between pipes and fittings with an interference fit up to a 6-inch diameter and is suitable for all classes and schedules of rigid PVC and CPVC (including Schedule 80 up to a 4-inch diameter). The light amber PVC and CPVC cement excels across a range of applications, including irrigation sprinklers, plumbing systems, and conduit. And thanks to its medium-bodied viscosity and fast relative set time, this solvent cement applies smoothly and sets quickly to facilitate efficient PVC and CPVC welding. Weld-On 790 should not be used as a transition cement between dissimilar materials (e.g. PVC and CPVC or ABS and PVC). It is also not suitable for applications requiring potable water, DWV (drain, waste, and vent), or sewer waste listed products per the plumbing and building codes. Refer to the pipe and fittings manufacturer’s instruction and the local plumbing and building codes for appropriate cement use.

• Medium-bodied, fast-setting, low-VOC multi-purpose cement for all classes and schedules with interference fit through 6" (160 mm) diameter, Sch. 80 through 4" (110 mm) diameter
• High-strength cement for PVC and CPVC pipe and fittings

Compatible with both PVC and CPVC piping, Weld-On 790 Multi-Purpose Solvent Cement offers versatility to contractors working with diverse piping systems. This pipe cement creates a deep, high-contact fusion between pipes and fittings with an interference fit up to a 6-inch diameter and is suitable for all classes and schedules of rigid PVC and CPVC (including Schedule 80 up to a 4-inch diameter). The light amber PVC and CPVC cement excels across a range of applications, including irrigation sprinklers, plumbing systems, and conduit. And thanks to its medium-bodied viscosity and fast relative set time, this solvent cement applies smoothly and sets quickly to facilitate efficient PVC and CPVC welding. Weld-On 790 should not be used as a transition cement between dissimilar materials (e.g. PVC and CPVC or ABS and PVC). It is also not suitable for applications requiring potable water, DWV (drain, waste, and vent), or sewer waste listed products per the plumbing and building codes. Refer to the pipe and fittings manufacturer’s instruction and the local plumbing and building codes for appropriate cement use.

• Medium-bodied, fast-setting, low-VOC multi-purpose cement for all classes and schedules with interference fit through 6" (160 mm) diameter, Sch. 80 through 4" (110 mm) diameter
• High-strength cement for PVC and CPVC pipe and fittings

Weld-OnŒ C-65Ž is a clear, low VOC emission, water-thin, solvent cleaner. It is specifically formulated to remove grease, oil and dirt from the bonding surfaces of PVC, CPVC, ABS and Styrene pipe and fittings. It is approved for Flowguard GoldŒ CTS plumbing systems.

APPLICATION: WELD-ON C-65 is an all purpose cleaner and can be used on all sizes, classes and schedules of PVC, CPVC, ABS and Styrene pipe and fittings. It must be used only as a cleaner, in conjunction with the appropriate primer and/or cement combination. WELD-ON C-65 can also be used as a brush cleaner. Detailed directions on making solvent cemented joints are printed on the container label. An installation DVD/CD covering solvent cementing is available. It not only describes the basic principles of solvent cementing, but also covers the handling, storage and use of our products. It is highly recommended that the installer review the instructions supplied by the pipe and fitting manufacturer.

• Meets SCAQMD Rule 1168/316A.
• Compliant with LEED ——Œ (Leadership in Energy and Environmental Design). When using this WELD-ON low VOC product, credit can be claimed for LEED Green Building Rating System _ Indoor Environmental Quality.

DIRECTIONS FOR USE:

• Before using this cleaner, pipe and fittings should be cut square, deburred and checked for proper fit.
• Use an applicator (e.g. dauber, brush top applicator or paintbrush) at least _ the size of the pipe diameter. Do not use a rag as repeated contact of cleaner-infused rag with skin may cause irritation or blistering.
• Apply C-65 freely to the socket keeping surface wet and applicator wet and in motion for 5 - 15 seconds. Be sure to use a scrubbing motion to clean off all grease, oil and dirt. Re-dip if necessary. Avoid puddling the socket.
• Apply C-65 to the pipe surface in the same manner equal to the depth of the socket.
• Repeat application to the fitting socket.
• Allow C-65 to dry and then apply appropriate WELD-ON primer and/or cement following instructions on the cans.

Weld-OnŒ C-65Ž is a clear, low VOC emission, water-thin, solvent cleaner. It is specifically formulated to remove grease, oil and dirt from the bonding surfaces of PVC, CPVC, ABS and Styrene pipe and fittings. It is approved for Flowguard GoldŒ CTS plumbing systems.

APPLICATION: WELD-ON C-65 is an all purpose cleaner and can be used on all sizes, classes and schedules of PVC, CPVC, ABS and Styrene pipe and fittings. It must be used only as a cleaner, in conjunction with the appropriate primer and/or cement combination. WELD-ON C-65 can also be used as a brush cleaner. Detailed directions on making solvent cemented joints are printed on the container label. An installation DVD/CD covering solvent cementing is available. It not only describes the basic principles of solvent cementing, but also covers the handling, storage and use of our products. It is highly recommended that the installer review the instructions supplied by the pipe and fitting manufacturer.

• Meets SCAQMD Rule 1168/316A.
• Compliant with LEED ——Œ (Leadership in Energy and Environmental Design). When using this WELD-ON low VOC product, credit can be claimed for LEED Green Building Rating System _ Indoor Environmental Quality.

DIRECTIONS FOR USE:

• Before using this cleaner, pipe and fittings should be cut square, deburred and checked for proper fit.
• Use an applicator (e.g. dauber, brush top applicator or paintbrush) at least _ the size of the pipe diameter. Do not use a rag as repeated contact of cleaner-infused rag with skin may cause irritation or blistering.
• Apply C-65 freely to the socket keeping surface wet and applicator wet and in motion for 5 - 15 seconds. Be sure to use a scrubbing motion to clean off all grease, oil and dirt. Re-dip if necessary. Avoid puddling the socket.
• Apply C-65 to the pipe surface in the same manner equal to the depth of the socket.
• Repeat application to the fitting socket.
• Allow C-65 to dry and then apply appropriate WELD-ON primer and/or cement following instructions on the cans.

Weld-OnŒ C-65Ž is a clear, low VOC emission, water-thin, solvent cleaner. It is specifically formulated to remove grease, oil and dirt from the bonding surfaces of PVC, CPVC, ABS and Styrene pipe and fittings. It is approved for Flowguard GoldŒ CTS plumbing systems.

APPLICATION: WELD-ON C-65 is an all purpose cleaner and can be used on all sizes, classes and schedules of PVC, CPVC, ABS and Styrene pipe and fittings. It must be used only as a cleaner, in conjunction with the appropriate primer and/or cement combination. WELD-ON C-65 can also be used as a brush cleaner. Detailed directions on making solvent cemented joints are printed on the container label. An installation DVD/CD covering solvent cementing is available. It not only describes the basic principles of solvent cementing, but also covers the handling, storage and use of our products. It is highly recommended that the installer review the instructions supplied by the pipe and fitting manufacturer.

• Meets SCAQMD Rule 1168/316A.
• Compliant with LEED ——Œ (Leadership in Energy and Environmental Design). When using this WELD-ON low VOC product, credit can be claimed for LEED Green Building Rating System _ Indoor Environmental Quality.

DIRECTIONS FOR USE:

• Before using this cleaner, pipe and fittings should be cut square, deburred and checked for proper fit.
• Use an applicator (e.g. dauber, brush top applicator or paintbrush) at least _ the size of the pipe diameter. Do not use a rag as repeated contact of cleaner-infused rag with skin may cause irritation or blistering.
• Apply C-65 freely to the socket keeping surface wet and applicator wet and in motion for 5 - 15 seconds. Be sure to use a scrubbing motion to clean off all grease, oil and dirt. Re-dip if necessary. Avoid puddling the socket.
• Apply C-65 to the pipe surface in the same manner equal to the depth of the socket.
• Repeat application to the fitting socket.
• Allow C-65 to dry and then apply appropriate WELD-ON primer and/or cement following instructions on the cans.