High-quality, hardened steel, hammer flaring tools for copper tubing are toolbox basics. Designed to make uniform, 45 degree flares on Type K soft copper water service tubing, REED’s flaring tools feature large pilots and knurled finger grip areas for added safety. REED offers hammer flaring tools in a variety of copper tubing sizes.

 To absorb impact shock on striking, it is recommended to only strike the flaring tool with a soft-faced brass hammer like REED's HAM3.

• Copper Tube Size: 1 1/2"
• Designed with larger pilots and finger grip areas for safety.
• Quality flaring tools for use on Type K soft copper tubing.

High-quality, hardened steel, hammer flaring tools for copper tubing are toolbox basics. Designed to make uniform, 45 degree flares on Type K soft copper water service tubing, REED’s flaring tools feature large pilots and knurled finger grip areas for added safety. REED offers hammer flaring tools in a variety of copper tubing sizes.

 To absorb impact shock on striking, it is recommended to only strike the flaring tool with a soft-faced brass hammer like REED's HAM3.

• Copper Tube Size: 2"
• Designed with larger pilots and finger grip areas for safety.
• Quality flaring tools for use on Type K soft copper tubing.

High-quality, hardened steel, hammer flaring tools for copper tubing are toolbox basics. Designed to make uniform, 45 degree flares on Type K soft copper water service tubing, REED’s flaring tools feature large pilots and knurled finger grip areas for added safety. REED offers hammer flaring tools in a variety of copper tubing sizes.

 To absorb impact shock on striking, it is recommended to only strike the flaring tool with a soft-faced brass hammer like REED's HAM3.

• Copper Tube Size: 3/4"
• AWWA Approved
• Designed with larger pilots and finger grip areas for safety.
• Quality flaring tools for use on Type K soft copper tubing.

• Application: Cast Iron; Ductile Iron
• FITS:
• Reed Cutter: H6; H8; H12
• Wheeler Rex: 95061; 95081; 95121
• Blade Exposure: 0.41  Blade Exposure determines wall thickness capacity of cutter wheel.
• All Reed cutter wheels are made from high shock-resistant tool steel.
• By using this higher quality raw material, Reed cutter wheels can be made thinner and can therefore cut pipe more easily and leave less burr.
• Also, because of their higher quality, certified material, only Reed cutter wheels can be heat-treated for the perfect balance between hardness and toughness to make Reed cutter wheels resist breakage and last longer.
• Reed offers the largest cutter wheel line for all types of pipe, tubing and conduit.

Robust Guillotine Pipe Cutters are designed to cut PE pipe from SDR15.5 to SDR9 within 1/8” (3 mm) of square on medium and high-density pipe.

• Cuts PE up to 12" (350 mm).
• Squarest cut available, within 1⁄8" (3 mm) on medium and high density pipe, due to strong frames and unique blade design.
• Saves facing cost: no facing needed for electrofusion, less needed for butt-fusion.
• Requires minimal clearance, only 4" – 6" (102 - 152 mm) around pipe.
• Clean and safe! No chips to clog valves and apertures.
• Many high quality cuts, with durable non-stick coated (resharpenable and replaceable) tool steel blade.
• Replacement Blades

• Application: PE
• SDR 17 - SDR9.3
• Pipe Capacity: 4" - 12" 
• Length: 51"
• MUST SHIP VIA TRUCK LINE

NOTES:

HPCs cut PE only and will not cut PVC or PP (polypropylene) pipe, such as Aquatherm®.

Temperature impacts pipe density. Cold temperatures (below freezing) can significantly shorten blade life.

Blade is very sharp. Take care when reaching in that area.

For operator and blade safety, always transport the cutter with the blade fully seated in the base of the cutter. Use the blade guard if available since it protects the blade and the operator.

Reed strongly recommends use of the PEGR7 Static Grounding Device (#04621) with Guillotine Cutters. Use a grounding device as a precaution against static build-up. Dissipate the charge and minimize the possibility of ignition.

• Replacement blade for REED HPC12 guillotine pipe cutter.
• Expect high quality cuts from this durable, non-stick coated, heat-treated, tool steel blade.
• Best performance when the tool and the pipe are kept clean and the blade edge is free of nicks.
• Blade can be sharpened before replacement is needed.

Robust Guillotine Pipe Cutters are designed to cut PE pipe from SDR15.5 to SDR9.

• Cuts PE up to 4" (125 mm).
• New all aluminum construction results in lighter weight and greater rigidity
• Greater capacity, up to 4.9 in O.D.   Slightly enlarged pipe capacity fits true 4 in DIPS and IPS for PE
• Aluminum rails and crosshead have a hard anodize finish to reduce wear on sliding surfaces
• Superior cuts with MADE IN USA blade
• Squarest cut available, within 1⁄8" (3 mm) on medium and high density pipe, due to strong frames and unique blade design.
• Saves facing cost: no facing needed for electrofusion, less needed for butt-fusion.
• Requires minimal clearance, only 4" – 6" (102 - 152 mm) around pipe.
• Clean and safe! No chips to clog valves and apertures.
• Many high quality cuts, with durable non-stick coated (resharpenable and replaceable) tool steel blade.
• Replacement Blades

• Application: PE
• SDR 15.5 - SDR9
• Pipe Capacity: 2 in O.D. minimum 4.9 in O.D. maximum  (48 – 125 mm O.D.)
• Pipe Range:  1 ½ in IPS – 4 in DIPS for SDR15.5 ‐ SDR9
• Length: 19"

NOTES:

HPCs cut PE only and will not cut PVC or PP (polypropylene) pipe, such as Aquatherm®.

Temperature impacts pipe density. Cold temperatures (below freezing) can significantly shorten blade life.

Blade is very sharp. Take care when reaching in that area.

For operator and blade safety, always transport the cutter with the blade fully seated in the base of the cutter. Use the blade guard if available since it protects the blade and the operator.

Reed strongly recommends use of the PEGR7 Static Grounding Device (#04621) with Guillotine Cutters. Use a grounding device as a precaution against static build-up. Dissipate the charge and minimize the possibility of ignition.

• Replacement blade for REED HPC4 guillotine pipe cutter.
• Expect high quality cuts from this durable, non-stick coated, heat-treated, tool steel blade.
• Best performance when the tool and the pipe are kept clean and the blade edge is free of nicks.
• Blade can be sharpened before replacement is needed.

Robust Guillotine Pipe Cutters are designed to cut PE pipe from SDR15.5 to SDR9 within 1/8” (3 mm) of square on medium and high-density pipe.

• Manual, guillotine style cutter slices smoothly through PE.
• All aluminum construction results in lighter tool weight and greater rigidity - 22%+ weight reduction versus prior HPC8 model.
• Greater pipe capacity, up to 9.06” O.D. fits true 8” DIPS and IPS for PE.
• Aluminum rails and crosshead have a hard anodized finish to reduce wear on sliding surfaces.
• Superior cuts with USA made blade.
• Squarest cut available, within 1⁄8" (3 mm) on medium and high density pipe, due to strong frames and unique blade design.
• Saves facing cost: no facing needed for electrofusion, less needed for butt-fusion.
• Requires minimal clearance, only 4" – 6" (102 - 152 mm) around pipe.
• Clean and safe! No chips to clog valves and apertures.
• Many high quality cuts, with durable non-stick coated (resharpenable and replaceable) tool steel blade.
• Replacement Blades

• Application: PE
• SDR 15.5 - SDR9
• Pipe Capacity: 3" - 8" DIPS & IPS
• Length: 29.6"

NOTES:

HPCs cut PE only and will not cut PVC or PP (polypropylene) pipe, such as Aquatherm®.

Temperature impacts pipe density. Cold temperatures (below freezing) can significantly shorten blade life.

Blade is very sharp. Take care when reaching in that area.

For operator and blade safety, always transport the cutter with the blade fully seated in the base of the cutter. Use the blade guard if available since it protects the blade and the operator.

Reed strongly recommends use of the PEGR7 Static Grounding Device (#04621) with Guillotine Cutters. Use a grounding device as a precaution against static build-up. Dissipate the charge and minimize the possibility of ignition.

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

• Replacement blade for REED HPC8 guillotine pipe cutter.
• Expect high quality cuts from this durable, non-stick coated, heat-treated, tool steel blade.
• Best performance when the tool and the pipe are kept clean and the blade edge is free of nicks.
• Blade can be sharpened before replacement is needed.

• Application: Steel; Stainless Steel
• FITS:
• Reed Cutter: 3-1; 3-3; 3-4; H4; LCRC4
• Wheeler Rex: 95041
• Blade Exposure: 0.32  Blade Exposure determines wall thickness capacity of cutter wheel.
• All Reed cutter wheels are made from high shock-resistant tool steel.
• By using this higher quality raw material, Reed cutter wheels can be made thinner and can therefore cut pipe more easily and leave less burr.
• Also, because of their higher quality, certified material, only Reed cutter wheels can be heat-treated for the perfect balance between hardness and toughness to make Reed cutter wheels resist breakage and last longer.
• Reed offers the largest cutter wheel line for all types of pipe, tubing and conduit.

• Application: Steel; Stainless Steel; Copper
• FITS:
• Reed Cutter: H6
• Wheeler Rex: 95061
• Blade Exposure: 0.39  Blade Exposure determines wall thickness capacity of cutter wheel.
• All Reed cutter wheels are made from high shock-resistant tool steel.
• By using this higher quality raw material, Reed cutter wheels can be made thinner and can therefore cut pipe more easily and leave less burr.
• Also, because of their higher quality, certified material, only Reed cutter wheels can be heat-treated for the perfect balance between hardness and toughness to make Reed cutter wheels resist breakage and last longer.
• Reed offers the largest cutter wheel line for all types of pipe, tubing and conduit.